I need help!

[Montesky]

(10-09-2011 02:02 PM)nemesis567 Wrote:  You check the normal boxes without animation and export hte .dae file.
Then you check everything off except for the animation and export as .dae
You rename the last dae to .dae_anim and place it in the anim folder.
It should work okay from there on.

Yes, but first you will need to check that animation run, not ? the modelviewer cant open dae_anim separately...

[santtex]

uum no idont :O

---

animation runs but models goes like that

[Montesky]

it the config in original mosnters... all ok here ??

bakeTransforms=0
exportPolygonMeshes=1
bakeLighting=0
isSampling=1
curveConstrainSampling=1
removeStaticCurves=0
exportCameraAsLookat=0
exportLights=1
exportCameras=1
exportJointsAndSkin=1
exportAnimations=1
exportTriangles=0
exportInvisibleNodes=0
exportNormals=1
exportTexCoords=1
exportVertexColors=1
exportVertexColorsAnimation=0
exportTangents=1
exportTexTangents=0
exportConstraints=1
exportPhysics=1
exportXRefs=1
dereferenceXRefs=0
cameraXFov=0
cameraYFov=1
.......................

[santtex]

yes that is ok

[Montesky]

Samttex.. you export settings does not have the animation chequered

maybe it is the problem

[nemesis567]

(10-09-2011 02:09 PM)Montesky Wrote:  

(10-09-2011 02:02 PM)nemesis567 Wrote:  You check the normal boxes without animation and export hte .dae file.

Then you check everything off except for the animation and export as .dae

You rename the last dae to .dae_anim and place it in the anim folder.

It should work okay from there on.

Yes, but first you will need to check that animation run, not ? the modelviewer cant open dae_anim separately...

Model view automattically loads any dae_anim files if they are in an anim folder inside the same folder as the model if I remember well.

[Montesky]

i checking your image captured XD

---

(10-09-2011 02:18 PM)nemesis567 Wrote:  

(10-09-2011 02:09 PM)Montesky Wrote:  

(10-09-2011 02:02 PM)nemesis567 Wrote:  You check the normal boxes without animation and export hte .dae file.

Then you check everything off except for the animation and export as .dae

You rename the last dae to .dae_anim and place it in the anim folder.

It should work okay from there on.

Yes, but first you will need to check that animation run, not ? the modelviewer cant open dae_anim separately...

Model view automattically loads any dae_anim files if they are in an anim folder inside the same folder as the model if I remember well.

Yeah.. for the rest of animations yess ))

The problem is the first try with your animated model... i test it directly from dae on modelviewer before making the entitie.. if not, later i will delete and delete a lot of fail meshes

[nemesis567]

I think that the first .dae file requires an idle animation of sorts that must come along with the mesh.

[santtex]

montesky can you make video tutorial where you have only that successful version animation and model ?

[Montesky]

(10-09-2011 02:44 PM)santtex Wrote:  montesky can you make video tutorial where you have only that successful version animation and model ?

it was for you #12


http://www.youtube.com/watch?v=K7b320yDjE0


EDIT: you say without errors.. i recording
the bad issue that i use 3dsmax

(10-09-2011 02:39 PM)nemesis567 Wrote:  I think that the first .dae file requires an idle animation of sorts that must come along with the mesh.

yess